D1844

Fujitsu D1844 Motherboard

Specification

Graphics

BIOS Listing

Motherboard Manual

Specification

LGA775 Socket Intel® Pentium® 4/Celeron
Intel® 915G Chipset
533/800MHz FSB
Power supply BTX (ATX compatible)
4 DIMM Slots (DDR 1)
- 184 pin, 2.5V, 64 bit, DDR400
- Max memory 4GB
- No ECC Support
Integrated Intel? GMA900 2D / 3D Video Controller - Dynamic Video memory Technology, 400 Mhz integrated 24-bit RAMDAC
Integrated AD1986 AC97 Audio Codec
- Line in
- Line out
- Mic in
Serial ATA Controller (2)
ATA 100 IDE Controller (slimline optical drive only)
1 x slimline floppy drive (optional)
1 PCI Express x16 (graphics)
1 x PCI Slot (32bit) - Riser card option
8 x USB ports (USB 2.0) - 2 x front, 4 x rear, 2 x internal
Integrated Broadcom BCM5751 LAN Controller (10/100/1000mbps)
- WoL Support
- AoL Support
Option for Internal Smartcard reader (USB)

Graphics

D1844 System Board

Connectors on D1844 System Board

D1844 Broadcom BCM5751 LAN Controller

LED 1 lights green = connection exists (e.g. to a hub)
LED 1 is blinking green = activity
LED 2 lights up differently depending on the transfer rate:
10 Mbit/s off
100 Mbit/s green
1000 Mbit/s yellow

D1844 Board Layout

1 = PCI slot for Riser card
2 = Floppy Disk Drive
3 = USB Connector
4 = Fan 2
5 = Power supply +12 V
6 = Fan 1 (CPU)
7 = IDE drives 1/2 (optical only)
8 = Serial ATA 1
9 = Serial ATA 2
10 = Power Supply
11 = Power Control
12 = S/PDIF (not an option for this config.)
13 = CD Audio Input
14 = Jumper
15 = PCI Express x1 Riser Slot

BIOS Listing

<F1> Info
-/+ Select item / Change Values
F9 Setup Defaults
Esc Exit
Enter Select Menu / Execute Command
F7 Previous Values

Main


		Normal Settings	Alternative Settings
System Time:		HH:MM:SS
System Date		MM:DD:YY
Standard IDE:	HL-DT-STLD-RW/DVD Drive (PM)
	PIO Mode	PIO 4
	DMA Mode	UDMA 2
	Silent Mode	Disabled	Enabled
	Password Status	not supported
	Change Password	press enter (greyed out)
Native IDE:	Samasung SP0411C (QM)
	Maximum Capacity	xxGB
	PIO Mode	PIO 4
	DMA mode	UDMA 6
	Silent Mode	silent	disabled, medium
	Password Status	not installed
	Change Password	press enter
Boot Options:	POST Errors	Halt On All Errors	No Halt On Any Errors
	Fast Boot	Enabled	Disabled
	Quiet Boot	Enabled	Disabled
	cME Video Mode (if using FirstWare RecoverPro)	640x480	800x600, 1024x768, 1280x1024
	Primary Display	PEG (PCI Express Graphics)	PCI
	Boot Menu	Enabled	Disabled
	PC Beep Volume	High	Low, Off
Boot Sequence:		ATAPI CD-ROM Drive
		Diskette
		Hard Drive
		Legacy LAN Card
		Boot Manage PXE, Slot 0300
Base Memory	640k
Extended Memory	502M

Advanced


		Normal Settings	Alternative Settings
Peripheral Configuration	Serial 1	Auto	Enabled Disabled
	Serial 2	Auto	Enabled Disabled
	Parallel	Auto	Enabled Disabled
	Parallel Mode	ECP	Bi Directional Printer EPP ECP
	USB Host Controller	Enabled	Disabled
	USB 2.0 Host Controller	Enabled	Disabled
	USB Legacy Support	Disabled	Enabled
	USB Boot Delay	(0's) greyed out
	ATA Controller Configuration:
	SATA Mode	Native	Compatible
	Primary IDE Channel	Enabled	Disabled
	Tertiary IDE Channel	Enabled	Disabled
	Quaternary	Enabled	Disabled
	Diskette Controller	Enabled	Disabled
	Mouse Controller	Auto Detect	Disabled Enabled
	LAN Controller	Enabled	Disabled
	LAN Remote Boot	Enabled	Disabled
	Audio Controller	Enabled	Disabled
PCI Configuration	PCI IRQ Line 1:	Auto	Disabled IRQ 3 IRQ 4 IRQ 5 IRQ 6 IRQ 7 IRQ 9 IRQ 10 IRQ 11 IRQ 12 IRQ 14 IRQ 15
	PCI IRQ Line 2:	Auto
	PCI IRQ Line 3:	Auto
	PCI IRQ Line 4:	Auto
	PCI IRQ Line 5:	Auto
	PCI IRQ Line 6:	Auto
	PCI IRQ Line 7:	Auto
	PCI IRQ Line 8:	Auto
Advanced System Configuration:	PCI Bus Parity Checking	Disabled	Enabled
	PCI Bus SERR for Video	Disabled	Enabled
	BIOS workspace location	Expansion ROM area	Top of base memory
	Limit CPUID Funtions	Disabled	Enabled
	Discard Timer Mode	1024 Clocks	128 clocks
	HDD Host Protected Area (if option purchased)	Enabled	Disabled
	Smart Device Monitoring	Enabled	Disabled
System Management:
	SM Fan Control	Auto (Optimum)	Enhanced Cooling(max), Silent(Reduced)
	SM Errror Halt	Disabled	Enabled
	Fan State:
	Power Supply	OK
	Fan 1 (CPU)	OK
	Fan 2	OK
	Thermal Sensor State:
	CPU	OK
	System	OK
	Battery State	OK
Reset Configuration Data		No	Yes
Hyperthreading		Enabled	Disabled

Security


	Normal Settings	Alternative Settings
Setup Password	Not installed
System Password	Not installed
Set setup password	Press enter
Setup password lock	Standard	Extended
Set system password	Press enter
System password mode	System	keyboard
System password lock	WOL Skip (greyed out)
cME Authentication Level (if Firstware option was purchased)	High	Medium, Low
System load	Standard	Diskette / CD rom lock
Setup prompt	Enabled	Disabled
Virus warning	Disabled	Enabled
Diskette write	Enabled	Disabled
Flash write	Enabled	Disabled
Memorybird System Lock	Disabled	Enabled
Smartcard systemlock	Disabled	Enabled
Embedded Security Chip (if TPM option was purchased)	Disabled	Enabled
Cabinet Monitoring	Disabled	Enabled

Power


	Normal Settings	Alternative Settings
APM Interface:	Enabled	Disabled
APM Power Saving:	Customized	Disabled Maximum Power Savings Maximum Performance
Standby Timeout	15 min	Disabled 2 min 5 min 10 min 30 min
Suspend Timeout	Disabled	2 min 15 min 30 min 1 h 2 h
Hard Disk Timeout	15 Min	Disabled 2 min 5 min 10 min
APM Resume Timer:	Disabled	Enabled
APM Resume Time	hh:mm:ss
ACPI Save to RAM	Enabled	Disabled
Safe to standby	Disabled	Enabled
Power On/Off:	hh:mm:ss
Power On Source	BIOS Controlled	ACPI Controlled
LAN	Enabled	Disabled
Wake Up Timer	Disabled	Enabled
Wake Up Time	hh:mm:ss
Wake Up Mode	Daily (greyed out)
Power Off Source
Software	Enabled	Disabled
Keyboard	Disabled	Enabled
Power Button	Enabled	Disabled
Power Failure Recovery	Previous State	Disabled, Always Off, Always On

Exit



Save Changes and exit
Discard Changes and exit
Get Default Values
Load Previous Values